The M10 tank destroyer, formally 3-inch Gun Motor Carriage, M10 was a United States tank destroyer of World War II based on the chassis of the M4 Sherman tank
About this creation
The M10 was numerically the most important U.S. tank destroyer of World War II and combined a reasonably potent anti-tank weapon with a turreted platform (unlike the previous M3 GMC, whose gun was capable of only limited traverse). Despite the introduction of more-powerful types as replacements, it remained in service until the end of the war. Some of those replacements were in fact modified and/or rebuilt from the M10 itself.
It was christened the "Wolverine" by the British, although unlike other vehicle names such as the M4 Sherman, the name was not adopted by American soldiers, who called it TD (a nickname for any tank destroyer in general) beyond its formal designation.
US combined-arms doctrine on the eve of World War II held that tanks should be designed to fulfill the infantry support and exploitation roles. The anti-tank warfare mission was assigned to a new branch, the tank destroyer force. Tank destroyer units were to be held as a reserve at the Corps or Army level, and were to move quickly to the site of any enemy tank breakthrough, maneuvering aggressively to destroy enemy tanks. This led to a requirement for very fast, well-armed vehicles. Though equipped with turrets (unlike most tank destroyers of the day), the typical American design was more heavily gunned, but more lightly armored, and thus more manoeuvrable, than a contemporary tank. The idea was to use speed and agility as a defense, rather than thick armor, to bring a powerful self-propelled gun into action against enemy tanks.
The M10 used a Sherman tank chassis with an open-topped turret mounting a 3" gun M7. This gun fired the Armor Piercing M79 shot that could penetrate 3 inches of armor at 1,000 yards at 30 degrees from vertical. Other ammunition carried throughout its service life included the Armor Piercing Capped Ballistic Cap (APCBC) M62 projectile, High Velocity Armor Piercing (HVAP) M93 shot, and Armor Piercing High Explosive (APHE); 54 rounds of 3-inch ammunition were carried. The rear of the turret carried two large counterweights which gave it a distinctive shape.
In its combat debut in Tunisia during the North African campaign, the M10 was successful as its 3-inch gun could destroy most German tanks then in service. The M10's heavy chassis did not conform to the tank destroyer doctrine of employing very light high-speed vehicles, and starting in mid-1944 it began to be supplemented by the M18 "Hellcat". Later in the Battle of Normandy, the M10's gun proved to be ineffective against the frontal armor of the newer German Tiger and Panther tanks unless firing HVAP rounds, but was effective against the most common tanks such as the Panzer IV medium tank and other lighter vehicles and self propelled guns. Tank Destroyer units had been supplemented with 90mm towed guns in partial anticipation of heavier German tanks, but their lack of mobility made employing them difficult.
Weight - 29.6 metric tons
Length - 6.8 m or 22.4 ft (w/ gun)
Width - 3 m or 10 ft
Height - 2.6 m or 8.4 ft
Crew - 5 (Commander, (3×) gun crew, driver)
Armor - 9 to 57 mm or .3 to 2 in
Main armament - 1x 3" (76.2 mm) Gun M7 w/54 rounds
Secondary armament - 1x .50 cal Browning M2HB machine gun w/300 rounds, 2x M1919 .30 machine guns w/2500 rounds
Engine - General Motors 6046 Twin Diesel 6-71 engine
Range - 300 km or 186 mi
Speed - 51 km/h or 32 mph
this is my favourite tank (destroyer) besides M18 Hellcat and M36 Slugger. the model is awesome, but i think it's a little bit too big for the minifigs. The body is spot on, specially the front. Overall a great creation. Could you attach an LDD file though, because i would LOVE to remake this into M36 Slugger and the credits would (mostly) be yours.