Done! Full instruction(no scope, yet) for my rifle.
About this creation
Here are the directions to my rifle. These directions are for bith you and me, as I like to rebuild me guns, and this will make it a lot easier, plus you guys can build it too! It has the same frame, with almost the same barrel as Jack Streats.
 Here is a picture of all the parts you need in the assembly phase, below are the instructions for each part.
The Firs Wall. This does not have to be peice fo peice.
 Heres what It will look like
 First piece, 9 holes
 Next layer very self explanitory just build what you see
 More stuff
 That space in the wall is for the trigger mech, very important.
 Next layer
 Another layer
 These two pins help hold the barrel in.
 Next layer
 Dont waste holed bricks here if you lack them
 A flat layer
 The top layer, the opening is for the bolt.
 Small components to add to the wall.
 Place this in the wall.
 Add this in
 Lastley add the bolt support in, the gun will be useless without this!
The other wall
 Heres what it look like.
 The first part, its mostly like the first wall, with slight mods.
 The flat part does nothing, its in streat's gun, so thats why its there.
 Next layer
 Next layer
 Cover the hole for the trigger mech
 Next layer, remeber the little bit that hangs oof the edge at the back!
 Next layer.
 Non holed layer.
 flat layer
 Top layer
 Small components
 Add the pins, the first pic was cause the blended in a bit on my camerea
 Add this bit in
 add this in, to finish the wall off.
 Here what it looks like.
 Only use the text if the pics dont work for you. two 4s with holes and pins
 11 holes with some pins
 a 9 holes with some pins
 Put it on the studed bricks
 Add these on.
 5 holes as you can see
 The axels are 3m long
 Add this stuff together
 add this on. It will be removed later.
 Put it here
 Add this here
 Add these (the first things)
 This is for support
 Cover with bricks, not the end where the stock attatches
 Add this layer on, with holes at the end
 Add this, thepins by the edges attatch it to the walls
 Attatch it like so
 Another layer
 the raised middle section
 Starting the stock
 These pins are three long
 Add this
 Add these
 add the 5 holer
 Add these holed bricks
 Build this
 Place it here
 Add this part
 Put it with the rest
 connest it to the rest
 Add this strap attatchment with another knot
 Start building up
 The second attatchment beam
 Add the holed bricks
 Add it in
 Add the next layer
 Another layer, minus a row
 The middle row
 This is for effect
 Remove these pins
 Slide it here
 Put the pins here, raise the bricks at the end a tad if it doent fit perfectly
 Here is a more suitable looking stock.. It just has a few more levels added on top and little bit on the bottom. Its from the third edition rifle thats black and grey and looks awesome, i just forget to take pics and ad it to moc pages. I have some video clips that might get added though.
The barel
 Here it is
 Starting the mag release
 Add the "ramp",(it wont be used, but it is in jack streats one).
 Working on stuff
 Trigger thingy
 Part of tyhe base
 add it in
 The rest of the base
 add it in
 add the 7 holed beam in
 Starting in the walls
 The middle
 The end
 Here it is, make another
 Here is the stopper
 finish it off
 add it in
 add the stopper wall in
 add the other one in
 Starting the top
 The sight
 put it in
 Add the new parts in
 Put it in as well as the part you saw on the side of the barel,the keep it ogether, when you drop th biPod
The roof
 The roof
 The first section
 The middle section
 The end, the L beams at the end,hold it into the barrel
 Put it all together
 Build this here
 A beam with pins
 Add more beams
 Make a duplicate with these pins sticking out
 Add the rubber band and the trigger
 Put it all together
 lokks like this
Interior little things
 Heres what we wre building
 These should be easy enough
 Build these two things
 Put them together
 Start the last part
 Add this
 Add the mag bolt hole, which does nothing :)
 Add the other side
 Build the thing here
 and place it on top
The Bolt
 Here it is
 Build the front
 The middle
 Put it here
 Put the parts from the sides in
 Make the bolt handdel, I didnt want to take it appart any further, but its pretty simple, and you can make what ever you like as long as it fits into the bolt hol in the wall good
 bottom veiw
 Build this in here
 Add the handle in
 Add these to the end of the other part
 Add the handle thing in
 Add the normal sight
 This is the hammer
 Put around like this
 Hook it here
 Do the same to the other side
Now go to my Lee enfeild biPod instuctions and build it.
The scope and mag are coming later.
Now you have all the parts, check the picture above to see if anything is unaccounted for. Now the assembly begins.
 Take the first wall (the one with the hole in the top.
 Insert the handel
 This is how it goes in
 Place the trigger mech in the little hole
 Place the rubber band on this pin
 Add that thing in
 Put the barrel in, and fix the trigger up
 Add those in
 Put the roof in these holes
 Clip it in here
 Place the bolt in the conveinient hole in the barrel
 Add this in
 Close the frame
 Click the strap in
 Add the snipper sight thing in, this makes aiming easier
 Add the scope in
 Add your BiPod
 Put the beam through
 Take step back and admire your gun.
So, any questions, just comment and get back to you as soon as I can. The scope and mag will come out tomorow.Please tell me what you think
Comments
|
|
same as below. Phillip@wikkard.net |
|
|
 |
I like it |
|
August 27, 2011 |
can u send me a parts list plz my email is wiljack_22@msn.com |
|
|
More from captin More across MOCpages
|
|
student teen kid toy play lego child video game hobby blocks construction toy legos fun games
|
